Garmin 12 Pin Orange Dual Band CHIRP Mix N Match Cable
We are proud to be an authorized dealer for this product.
What does this mean to you as a customer?
Buying from an authorized dealer means you are getting the best products and equipment from a reliable and knowledgeable source. We are always ready to answer any questions you may have regarding the product and installation. This product is covered under the manufacturers original warranty.
In an industry where websites and companies come and go, BOE Marine has been serving boat owners for over 20 years. We will be here after you have made your purchase, while many others will be a memory. When you buy from us, you do so with peace of mind.
Garmin 12-Pin Mix & Match Cable for Chirp TransducersAirmar's Garmin Mix & Match CableFeatures:12-PinSpecifically for Chirp Transducers ...
Want it Friday, May. 10? Choose Two-Day Shipping at checkout. Details
SKU
AIR-MMC-12G
Mix and Match Cables for CHIRP Transducers
Many CHIRP transducers are now made as Mix and Match models. These versions have a common base transducer with an attached 9-meter cable, plus an interchangeable short (1-meter) brand-specific adapter cable.
The permanently-attached 9-meter cable ends in an Airmar 12-pin connector. This cable is run up through the boat to the equipment location. The short adapter cable connects to the transducer cable at one end and to the equipment at the other end.
Both parts are needed for an installation. If the user changes equipment brand at some later time, the transducer and its attached cable can be left in place and only the adapter cable needs to be replaced.
Note that CHIRP Mix and Match cables cannot be used with conventional 50/200kHz transducers.
All the available CHIRP Mix and Match adapter cables are shown below. The same cables are used for all CHIRP transducers irrespective of their power rating.
The permanently-attached 9-meter cable ends in an Airmar 12-pin connector. This cable is run up through the boat to the equipment location. The short adapter cable connects to the transducer cable at one end and to the equipment at the other end.
Both parts are needed for an installation. If the user changes equipment brand at some later time, the transducer and its attached cable can be left in place and only the adapter cable needs to be replaced.
Note that CHIRP Mix and Match cables cannot be used with conventional 50/200kHz transducers.
All the available CHIRP Mix and Match adapter cables are shown below. The same cables are used for all CHIRP transducers irrespective of their power rating.
BOE Marine is known for providing the absolute best installations on the brands we carry. We are pleased to expand our footprint in partnership with companies that share the same ideals as us. Listed below you will find our Installation Partners in key regions around the country. You can contact these companies directly and get the same great service you expect from BOE Marine. Through our partnerships you are able to order your equipment at the best prices, tax free, from our website. Then have one of our Installation Partners perform a high quality installation.
Our program is built upon a high degree of accountability. Our Installation Partners expect us to give great advice, prices, and supply all of the parts needed for the install. And we expect our Installation Partners to provide an expert installation in a timely manner and provide support for any equipment malfunctions or installation issues.
As the customer, you can be assured that you are buying from a dealer authorized in the brands we carry. And you will receive uncompromising advice and support on the local level from the Installation Partner, or via phone with BOE Marine. We feel there is no better package to get you the best pricing along with experienced local service.
Mid-Atlantic (MD, DE, DC)
Serviced by BOE Marine 866-735-5926
Palm Beach / Treasure Coast
Serviced by BOE Marine of Stuart 772-600-5701
Florida West Coast (Tampa/St Pete Area)
Bluewater Custom Marine - 727-488-7171
Mobile Electronics Installation
St. Petersburg, FL
CONTACT: Martin Warren
Email: [email protected]
http://www.bluewatercustommarine.com
Fort Lauderdale - Miami Dade
Parker Yacht - 954-463-1515
225 SW 32nd Street
Fort Lauderdale, FL 33315
CONTACT: Ole Parker
Email: [email protected]
http://www.parkeryacht.com
Alabama
HMS Marine Electric, LLC - 251-591-3283
400 Myrtle Avenue
Fairhope, AL 36532
CONTACT: Maclin Smith Jr.
Email: [email protected]
Website
Cape Cod & Islands
Dempsey Marine Electronics & Electrical - 508-360-1094
234 Queen Anne Road #2
Harwich Mass 02645
CONTACT: Tom Dempsey
Email: [email protected]
http://www.dempseymarine.com
Texas - Houston/Galveston & Surrounding Areas
Bill Platt Electronics - 409-739-3489
3501 Tallow Forest St
Dickinson, TX 77539
CONTACT: Bill Platt
Email: [email protected]
http://billplattfishing.com
Washington DC / Occoquan
Jimmy's Mobile Marine
James Deuterman
9192 Big Springs Loop
Bristow, VA 20136
703-801-9488
Email: [email protected]
Baton Rouge, LA
David Wade Marine
Casey
18150 Petroleum Dr
Baton Rouge, Louisiana
(225) 752-3789
Email: [email protected]
Bermuda
Spar Yard Marine
Kareem
6 Spar Lane Sandy’s, MA01
Bermuda
Email: [email protected]
Long Island, NY
Jeff's Marine Electronics
8 Rugby Dr
Shirley, NY 11967
631-874-0070 or 631-469-1645 (cell)
Installers - Do you have what it takes to be an Authorized BOE Installation Partner? If you can demonstrate a proven track record of impeccable customer service and expert installations then we will consider adding you to this list in markets not already covered. Please email [email protected] to inquire.
| SKU | AIR-MMC-12G |
|---|---|
| Price | $102.00 |
| Manufacturer | Airmar |
| Custom Discount | Discount - Electronic Products |
Products from the same brand
-
-
Airmar WS-C10 NMEA 0183 Cable f/Heading Sensors Weather
Special Price $105.76 Regular Price $111.33WS-C10 NMEA 0183 Cable for Heading Sensors WeatherWith NMEA 0183 output only. End in an Airmar 8-Pin connector which can be removed for connection to bare-wire devices.10M/33' ... Learn More
Tips
This section shows tips for this product from our sales team.
There are not any Tips for this product yet.
Product Questions
Answer:
This wire is for Mix and match transducers only. If your B260 is a mix and match it will have a similar short extension on it for your furuno. You could then swap that cable with this one. It sounds like you may not have a mix and match so I would recommend using the Garmin wire block adapter. Here is the link- https://www.boemarine.com/garmin-bare-wire-transducer-to-12-pin-sounder-wire-block-adapter.html
By Carson Orellana on 05 June, 2023
Answer:
Please email us your order info and we can send out the lock. Thank you!
By Kathryn France on 10 May, 2022
Answer:
If your unit has a 12-pin output on it then yes this will work.
By Emily Powers on 13 May, 2021
Thank you for the vote.
Join Our Discussion
Hi guest, this is a general discussion area where you can give any comment, feedback or suggestion and your experience regarding this product.